Company news
-
What Is The Impact of Incorrect PCBA Board Design?
1. The process side is designed on the short side. 2. Components installed near the gap may be damaged when the board is cut. 3. PCB board is made of TEFLON material with thickness of 0.8mm. The material is soft and easy to deform. 4. PCB adopts V-cut and long slot design process for transmission...Read more -
What Sensors Are on The SMT machine?
1. Pressure sensor of SMT machine Pick and place machine, including various cylinders and vacuum generators, have certain requirements for air pressure, lower than the pressure required by the equipment, the machine can not operate normally. Pressure sensors always monitor pressure changes, once ...Read more -
How To Weld Double-sided Circuit Boards?
I. Double-sided circuit board characteristics The difference between single-sided and double-sided circuit boards is the number of layers of copper. Double-sided circuit board is a circuit board with copper on both sides, which can be connected through holes. And there is only one layer of copper...Read more -
What Are The Solutions to PCB Bending Board and Warping Board?
NeoDen IN6 1. Reduce the temperature of reflow oven or adjust the rate of heating and cooling of the plate during reflow soldering machine to reduce the occurrence of plate bending and warping; 2. The plate with higher TG can withstand higher temperature, increase the ability to withstand pressur...Read more -
How Can Pick and Place Errors Be Reduced or Avoided?
When the SMT machine is working, the easiest and most common mistake is to paste the wrong components and install the position is not correct, so the following measures are formulated to prevent. 1. After the material is programmed, there must be a special person to check whether the component va...Read more -
Four Types of SMT Equipment
SMT equipment, commonly known as SMT machine. It is the key equipment of surface mount technology, and it has many models and specifications, including large, medium and small. Pick and place machine is divided into four types: assembly line SMT machine, simultaneous SMT machine, sequential SMT m...Read more -
What Is The Role of Nitrogen in Reflow Oven?
SMT reflow oven with nitrogen (N2) is the most important role in reducing the welding surface oxidation, improve the wettability of welding, because nitrogen is a kind of inert gas, not easy to produce compounds with metal, it can also cut off the oxygen in the air and metal contact at high tempe...Read more -
How to Store PCB Board?
1. after the production and processing of PCB, vacuum packaging should be used for the first time. There should be desiccant in the vacuum packaging bag and the packaging is close, and it can not contact with water and air, so as to avoid the soldering of reflow oven and product quality affected ...Read more -
What Are The Causes of Chip Component Cacking?
In the production of PCBA SMT machine, the cracking of chip components is common in the multilayer chip capacitor (MLCC), which is mainly caused by thermal stress and mechanical stress. 1. The STRUCTURE of MLCC capacitors is very fragile. Usually, MLCC is made of multi-layer ceramic capacitors, s...Read more -
Precautions for PCB Welding
1. Remind everyone to check the appearance first after getting the PCB bare board to see whether there is short circuit, circuit break and other problems. Then get familiar with the development board schematic diagram, and compare the schematic diagram with the PCB screen printing layer to avoid ...Read more -
What Is The Importance of Flux?
NeoDen IN12 reflow oven Flux is an important auxiliary material in PCBA circuit board welding. The quality of flux will directly affect the quality of reflow oven. Let’s analyze why flux is so important. 1. flux welding principle Flux can bear the welding effect, because the metal atoms are...Read more -
Causes of Damage-Sensitive Components (MSD)
1. The PBGA is assembled in the SMT machine, and the dehumidification process is not carried out before welding, resulting in the damage of PBGA during welding. SMD packaging forms: non-airtight packaging, including plastic pot-wrap packaging and epoxy resin, silicone resin packaging (exposed to ...Read more
